By Instruction for Bathtub Installation
By Instruction for Bathtub Installation
Blog Article
What're your thoughts on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a tub isn't exactly rocket science, yet it does require solid plumbing, carpentry, and in some cases, tiling skills. Changing an old tub with a brand-new one is likewise a moderately tough job. If the old bathtub is conveniently obtainable, the task can relocate immediately; if you need to open up a wall surface to get rid of the old bathtub and place the brand-new bath tub, the job is a lot harder. In either instance, the project is within a residence handyman's abilities, although you will need a helper to vacate the old bathtub and embeded in the brand-new one. See to it you have qualified on your own for the job and also fit attempting it. Rather than employing a specialist to take over a halfway-completed task, it is much better to consider utilizing one before you start. Chances are you might require an expert plumber to make tube links.
This article will certainly aid you set up a brand-new bath tub in your restroom if you have actually currently gotten a brand-new tub as well as do not require to change the plan of your previous water system pipelines.
Your devices as well as product list should comprise the following:
Preparing for the Setup
First of all, the supporting frame supplied with the bath needs to be fitted (if needed) according to the producer's instructions. Next off, fit the taps or mixer to the bath tub. When suitable the faucet block, it is necessary to make sure that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets device to avoid pressure on the tub.
Fit the versatile tap adapters to the bottom of the two faucets utilizing 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize all of the provided washers.
Link the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath should now be ready to be suited its last setting.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is detach the water. After doing so, activate the faucets to drain any water staying in the system. The process of removing the existing faucets can be rather problematic due to the limited gain access to that is commonly the situation.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the faucets. Have a towel all set for the remaining water that will certainly originate from the pipes. As soon as the supply pipes have actually been removed, make use of the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from turning throughout this process. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any type of old securing substance.
Before going on to fit the brand-new taps, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bathtub
Using the two wooden boards under its feet, place the bathtub in the required position. The wooden boards are handy in equally spreading the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The following objective is to make sure that the bath tub is leveled all round. This can be attained by examining the level as well as readjusting the feet on the bath tub up until the spirit level reviews level.
To mount faucets, fit the bottom of the outermost flexible faucet port to the appropriate supply pipeline by making a compression join; then do the same for the various other tap.
Activate the water supply as well as check all joints and also new pipework for leakages as well as tighten them if necessary. Load the bathtub as well as likewise examine the overflow outlet and also the typical electrical outlet for leakages.
Finally, take care of the bathroom paneling as described in the maker's instruction manual. Tiling as well as securing around the bath tub should wait up until the bathtub has been utilized a minimum of once as this will certainly settle it into its final position.
Suitable New Touches
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the string. One end of the port fits on the plastic tail of the faucet and also the other end supplies a connection to the current supply pipelines.
If you require to fit a monobloc, then you will certainly call for lowering couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin ensuring that the washing machines remain in place in between the faucet and also the sink. Protect the tap in position with the maker provided backnut. Once the faucet is safely in position, the supply pipes can be attached to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal tap ports. The former type needs to be connected to the faucet ends first, tightening up just by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bath fulfills the tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to crack an inflexible seal, triggering the water to permeate the wall between the bath as well as the tiling, resulting in issues with dampness and feasible leaks to the ceiling listed below.
You can select from a range of coloured sealants to blend in your components and also fittings. They are marketed in tubes as well as cartridges, and are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched paper or soft rope. Remember to constantly fill up the bath tub with water before securing, to enable the motion experienced when the bathtub is in usage. The sealant can fracture fairly very early if you do not consider this motion before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are likewise conveniently offered on the marketplace. It is recommended to fit the floor tiles using waterproof or waterproof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an enthusiastic person who reads about A Step-by-Step Guide to Installing a Bathtub, I figured sharing that piece of content was worthwhile. Liked our piece? Please share it. Let another person locate it. I am grateful for your time. Come back soon.
Get the best, call! Report this page