Mounting A Tub
Mounting A Tub
Blog Article
They are making a number of great pointers regarding How to Install a Bathtub as a whole in this content followed below.
Setting up a tub isn't exactly brain surgery, however it does need solid plumbing, woodworking, as well as in some cases, tiling skills. Changing an old tub with a new one is additionally a reasonably challenging task. If the old bathtub is readily obtainable, the job can move easily; if you have to open up a wall surface to remove the old bathtub and position the brand-new tub, the task is a lot harder. In either case, the task is within a house handyman's abilities, although you will require an assistant to leave the old tub as well as set in the brand-new one. Make sure you have actually qualified on your own for the job and also are comfortable trying it. Rather than employing a specialist to take control of a halfway-completed job, it is far better to think about using one before you start. Chances are you might require an expert plumber to make tube links.
This short article will aid you install a brand-new bathtub in your restroom if you have actually already purchased a brand-new tub as well as do not need to alter the setup of your previous supply of water pipelines.
Your tools as well as product checklist ought to consist of the following:
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is detach the water system. After doing so, activate the faucets to drain pipes any water remaining in the system. The process of eliminating the existing taps can be quite problematic because of the restricted gain access to that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have been eliminated, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this process. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any old sealing compound.
Before proceeding to fit the new taps, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end provides a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will require decreasing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the installing opening in the bath/basin guaranteeing that the washers are in area in between the faucet as well as the sink. Safeguard the faucet in position with the maker offered backnut. When the tap is securely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal faucet ports. The former kind must be connected to the faucet finishes first, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Setting up the Bathtub
Making use of both wooden boards under its feet, place the tub in the required placement. The wooden boards are useful in equally spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto four tiny points.
The next objective is to make sure that the bathtub is leveled all round. This can be attained by checking the level as well as adjusting the feet on the bath tub until the level checks out level.
To mount taps, fit all-time low of the furthest adaptable tap port to the appropriate supply pipeline by making a compression join; after that do the same for the other faucet.
Turn on the supply of water and inspect all joints and brand-new pipework for leakages and tighten them if essential. Fill up the bath tub and also inspect the overflow outlet as well as the regular outlet for leakages.
Lastly, fix the bath paneling as explained in the manufacturer's user's manual. Tiling and sealing around the bath tub ought to wait till the bathtub has been made use of a minimum of when as this will resolve it into its last position.
Getting ready for the Installation
First of all, the sustaining framework provided with the bath must be fitted (if called for) according to the producer's guidelines. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to make sure that if the tap features a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets device to prevent stress on the bathtub.
Fit the versatile faucet adapters to the bottom of the two taps utilizing 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bathroom. Make use of the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you utilize every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom must currently prepare to be suited its last placement.
Tiling Around the Bath tub
In the location where the bathroom fulfills the floor tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to split a stiff seal, triggering the water to permeate the wall surface between the bath and the tiling, leading to difficulties with wetness and also feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your components and also installations. They are offered in tubes as well as cartridges, and are capable of sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched newspaper or soft rope. Remember to always load the bath tub with water prior to securing, to permit the activity experienced when the bathtub is in use. The sealer can fracture rather very early if you do not take into consideration this motion before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also easily readily available on the marketplace. It is recommended to fit the tiles using waterproof or water resistant adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I came across that content on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while exploring the search engines. Enjoyed our content? Please share it. Let other people locate it. Thanks for your time invested reading it.
Book Today!
Report this page